Sterilisator Memmert SN30

Jual Sterilisator Memmert SN30

Sterilisator Memmert SN30 Standard Delivery Steriliser

The SN30 Standard Delivery Steriliser is an essential tool for laboratory sterilisation, ensuring reliable and safe operation with advanced features such as Setpoint Wait, which guarantees that sterilisation begins only once the set temperature is reached.

Key Features

• Setpoint Wait: Ensures sterilisation starts only when the set temperature is reached, applicable with freely positionable Pt100 temperature sensors to guarantee reliable sterilisation.

Temperature Specifications

• Setting Temperature Range: +20 to +250 °C
• Setting Accuracy: Up to 99.9 °C: 0.1 / from 100 °C: 0.5
• Working Temperature Range: At least 5 above ambient temperature to +250 °C
• Temperature Sensor: 1 Pt100 sensor DIN class A in 4-wire-circuit

Control Technology

• ControlCOCKPIT: SingleDISPLAY adaptive multifunctional digital PID-microprocessor controller with high-definition TFT-colour display
• Timer: Digital backwards counter with target time setting, adjustable from 1 minute to 99 days
• Function SetpointWAIT: Process time starts only when the set temperature is reached
• Calibration: Three freely selectable temperature values
• Adjustable Parameters: Temperature (Celsius or Fahrenheit), air flap position, programme time, time zones, summertime/wintertime

Ventilation

• Convection: Natural convection
• Fresh Air: Pre-heated fresh air admixture by electronically adjustable air flap
• Vent: Vent connection with restrictor flap

Communication

• Documentation: Programme stored in case of power failure
• Programming: AtmoCONTROL software for reading out, managing, and organising the data logger via Ethernet interface. USB stick with AtmoCONTROL software available as an accessory (on demand)

Safety

• Temperature Control: Adjustable electronic overtemperature monitor and mechanical temperature limiter TB, protection class 1 according to DIN 12880, switches off heating approximately 20°C above nominal temperature
• Autodiagnostic System: For fault analysis

Standard Equipment

• Works Calibration Certificate: Calibration at +160°C
• Door: Fully insulated stainless steel door with 2-point locking (compression door lock)
• Internals: 1 electropolished stainless steel grid
• Stainless Steel Interior: Easy-to-clean, reinforced by deep drawn ribbing with integrated and protected large-area heating on four sides
• Volume: 32 l
• Dimensions (Interior): 400 x 320 x 250 mm (w x h x d)
• Max. Number of Internals: 3
• Max. Loading of Chamber: 60 kg
• Max. Loading per Internal: 20 kg
• Textured Stainless Steel Casing
• Dimensions (Exterior): 585 x 704 x 434 mm (w x h x d, +56 mm door handle)
• Housing: Rear zinc-plated steel

Electrical Data

• Voltage Electrical Load:
  • 230 V, 50/60 Hz, approx. 1600 W
  • 115 V, 50/60 Hz, approx. 1600 W

Ambient Conditions

• Set Up: Minimum distance of 15 cm from the wall, 20 cm from the ceiling, and 5 cm from side walls or nearby appliances
• Altitude of Installation: Max. 2,000 m above sea level
• Ambient Temperature: +5 °C to +40 °C
• Humidity RH: Max. 80%, non-condensing
• Overvoltage Category: II
• Pollution Degree: 2

Packing/Shipping Data

• Transport Information: Appliances must be transported upright
• Customs Tariff Number: 8419 8998
• Country of Origin: Federal Republic of Germany
• WEEE-Reg.-No.: DE 66812464
• Dimensions (Including Carton): 660 x 890 x 650 mm (w x h x d)
• Net Weight: Approx. 46 kg
• Gross Weight (Carton): Approx. 62 kg

Standard units are safety-approved and bear the test marks CE, LGA, VDE, and UL.