Steriliser SN55 Single DISPLAY Memmert

Jual Steriliser SN55 Single DISPLAY Natural air circulation Memmert

SF30 Standard Delivery Steriliser

The SF30 Standard Delivery Steriliser offers precise and reliable sterilisation with advanced safety features, ideal for laboratory use. The Setpoint Wait function ensures that sterilisation only begins when the set temperature is reached, guaranteeing consistent results.

Steriliser SN55 Single DISPLAY Memmert Temperature Specifications

• Setting Temperature Range: +20 to +250 °C
• Setting Accuracy: Up to 99.9 °C: 0.1 / from 100 °C: 0.5
• Working Temperature Range: At least 10 °C above ambient temperature to +250 °C
• Temperature Sensor: 1 Pt100 sensor DIN class A in 4-wire-circuit

Control Technology

• ControlCOCKPIT: SingleDISPLAY adaptive multifunctional digital PID-microprocessor controller with high-definition TFT-colour display
• Timer: Digital backwards counter with target time setting, adjustable from 1 minute to 99 days
• Function SetpointWAIT: Process time does not start until the set temperature is reached
• Calibration: Three freely selectable temperature values
• Adjustable Parameters: Temperature (Celsius or Fahrenheit), fan speed, air flap position, programme time, time zones, summertime/wintertime

Ventilation

• Fan: Forced air circulation by quiet air turbine, adjustable in 10% steps
• Fresh Air: Pre-heated fresh air admixture by electronically adjustable air flap
• Vent: Vent connection with restrictor flap

Communication

• Documentation: Programme stored in case of power failure
• Programming: AtmoCONTROL software for reading out, managing, and organising the data logger via Ethernet interface (temporary trial version available). USB stick with AtmoCONTROL software available as accessory (on demand)

Safety

• Temperature Control: Adjustable electronic overtemperature monitor and mechanical temperature limiter TB, protection class 1 according to DIN 12880, switches off heating approximately 20°C above nominal temperature
• Autodiagnostic System: For fault analysis

Standard Equipment

• Works Calibration Certificate: Calibration at +160°C
• Door: Fully insulated stainless steel door with 2-point locking (compression door lock)
• Internals: 1 electropolished stainless steel grid
• Stainless Steel Interior: Easy-to-clean, reinforced by deep drawn ribbing with integrated and protected large-area heating on four sides
• Volume: 32 l
• Dimensions (Interior): 400 x 320 x 250 mm (depth less 39 mm for fan)
• Max. Number of Internals: 3
• Max. Loading of Chamber: 60 kg
• Max. Loading per Internal: 20 kg
• Textured Stainless Steel Casing
• Dimensions (Exterior): 585 x 704 x 434 mm (depth +56 mm door handle)
• Housing: Rear zinc-plated steel

Electrical Data

• Voltage Electrical Load:
  • 230 V, 50/60 Hz, approx. 1600 W
  • 115 V, 50/60 Hz, approx. 1600 W

Ambient Conditions

• Setup: Minimum distance of 15 cm from the wall, 20 cm from the ceiling, and 5 cm from side walls or nearby appliances
• Altitude of Installation: Max. 2,000 m above sea level
• Ambient Temperature: +5 °C to +40 °C
• Humidity RH: Max. 80%, non-condensing
• Overvoltage Category: II
• Pollution Degree: 2

Packing/Shipping Data

• Transport Information: Appliances must be transported upright
• Customs Tariff Number: 8419 8998
• Country of Origin: Federal Republic of Germany
• WEEE-Reg.-No.: DE 66812464
• Dimensions (Including Carton): 660 x 890 x 650 mm
• Net Weight: Approx. 46 kg
• Gross Weight (Carton): Approx. 62 kg